1. OPUS at UTS

Browsing byAuthorClemon, L

Jump to: 0-9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
or enter first few letters:  
Showing results 1 to 20 of 25  next >
Issue DateTitleAuthor(s)
2020-01-01A flexible hair-like laser induced graphitic sensor for low flow rate sensing applicationsAbbasnejad, B; McGloin, D; Clemon, L
2022-01-01A Reeb Graph Approach for Faster 3D PrintingKhatkar, J; Clemon, L; Fitch, R; Mettu, R
2021-09-30Additive manufacturing opportunities for Australia’s agriculture, fisheries and forestry sectorsClemon, L; Guertler, M; Tomidei, L; Edwards, R
2022-01-01BENEFIT OF OPTIMAL ACTUATOR SELECTION - A COMPARATIVE STUDYHanna, P; Carmichael, M; Clemon, L
2024-01-01BIOROBOTIC ACTUATOR SELECTION SPACE MAPPINGHanna, P; Carmichael, M; Clemon, L
2025-05Computational and experimental analysis of a novel triply periodic minimal surface heat sink with phase change materialArqam, M; Raffa, LS; Spisiak, S; Clemon, L; Luo, Z; Ryall, M; Islam, MS; Bennett, NS
2024-10-18Coordinated Multi-arm 3D Printing using Reeb DecompositionKhatkar, J; Sukkar, F; Clemon, L; Mettu, R
2022-01-01Coordinated Toolpath Planning for Multi-Extruder Additive ManufacturingKhatkar, J; Yool, C; Fitch, R; Clemon, L; Mettu, R
2021-01-01Development of an Organisational Framework for the Optimal and Efficient Selection of ActuatorsHanna, P; Carmichael, M; Clemon, L
2019-08-14DIMENSIONAL COMPARISON OF A COLD SPRAY ADDITIVE MANUFACTURING SIMULATION TOOLMurray, R; Foy, G; Clemon, L
2020-11-16Directed Graphical Model for Real-Time Process Monitoring in Additive ManufacturingClemon, L
2021-07-16Directed Graphical Model for Real-Time Process Monitoring in Additive ManufacturingClemon, L
2016-08-10Energy and Emission Estimation Uncertainty in Fused Deposition Modeling for a Job-ShopClemon, L; Bourell, D; Crawford, R; Seepersad, C; Beaman, J; Fish, S; Marcus, H
2025-01Experimental investigation of the performance of a phase change material thermal management module under vacuum and atmospheric pressure conditionsSueza Raffa, L; Ryall, M; Bennett, NS; Clemon, L
2024-10-23Improving the strength of Fused Filament Fabrication parts by non-planar alignment of material extrusion with stress vectorsEdwards, R; Clemon, L
2021-01-01Increased Strength of 3D Printed Parts With Z-Pin ApproachClemon, L; Christopher, K
2021-01-01INFLUENCING THE MECHANICAL PROPERTIES OF FUSED FILAMENT FABRICATION PARTS BY NON-PLANAR MATERIAL EXTRUSIONEdwards, R; Clemon, L
2024-01-01MATERIAL EXTRUSION INFILL STRENGTH UNDER DIFFERENT TOOLPATHSClemon, L; Edwards, R; Rizvi, D
2024-09Numerical and experimental investigation of a phase change material radial fin heat sink for electronics coolingArqam, M; Raffa, LS; Clemon, L; Islam, MS; Ryall, M; Bennett, NS
-Powder bed fusion factory productivity increases using discrete event simulation and genetic algorithmAl-zqebah, R; Guertler, M; Clemon, L
Showing results 1 to 20 of 25  next >